Denis LedererCanadian Waterproofing Systems · Victoria BC ☎ 236-240-7663

Flat roofing · Victoria & Vancouver Island

Flat roofing in Victoria, BC — TPO, PVC and torch-on.

Flat roofs are where I’m hired most: as the project manager who specifies the system, the specialist who installs the hard ones, and the guy companies call when a flat roof has to be right. I’ve put down single-ply and torch-on roofs from a 25,000 sq ft warehouse to backyard sundecks, and my TPO installation videos have been watched about 165,000 times.

TPO single-ply flat roof in Gordon Head, Victoria — a large light-grey membrane field with welded seams and vent caps above the ocean
TPO roof / fascia install, Gordon Head. A big single-ply roof on a waterfront new build, 2024 — Denis’s scope on this job was the fascia and panel work. Photo: Golden Rule Roofing.

Soprema Mammouth

The flat roof system I know best is Soprema’s Mammouth line. SBS modified bitumen membranes, most of them on larger commercial roofs. I’ve installed Mammouth for years, and Soprema trained me on it on site. Bill Bowers, who works for Soprema, ran the training. What I bring is the experience: how this membrane goes down, where it fails when a crew rushes it, and how the details have to be built so it never gets the chance.

Single-ply: TPO and PVC

A single-ply roof is one continuous membrane, TPO or PVC, rolled out in wide sheets with the seams heat-welded together. Done right, the seam is the strongest part of the roof. There are three ways to put it down:

  • Mechanically attached — fasteners and plates along the seams. The workhorse method for most commercial and residential flat roofs.
  • Fully adhered, the membrane is glued down. Smoothest finish, best on roofs people look down on from above.
  • Point-affixed / RhinoBond: induction-welded plates under the membrane. No seam fasteners, excellent wind uplift resistance.

I worked extensively with Mule-Hide TPO systems, up to 20-year manufacturer system warranties when installed to spec. White TPO also reflects summer heat instead of cooking your top floor.

Cold-ply: flat roofing without torches

Not every building should have an open flame on its roof. Occupied buildings, wood-frame construction, heritage work, and insurers who simply say no. Cold-ply systems go down without a torch:

  • Soprema cold-applied SBS, the Neo and Mammouth membranes in self-adhered and cold-adhesive form. The same modified bitumen toughness as torch-on, glued down instead of melted down.
  • Single-ply TPO and PVC, the seams are welded with hot air, not open flame. There is no torch anywhere on the roof.

No torch also means no fire watch, and an easier conversation with your insurance company. The trade-off is conditions: adhesives want a dry roof and reasonable temperatures, and the detailing has to be exact, because there is no flame to forgive a sloppy lap. If your building is a no-torch building, say so up front and I’ll spec the roof that way.

Torch-on (SBS modified bitumen)

Torch-on is two plies of modified bitumen membrane melted onto the roof with an open-flame torch. It is heavy, tough, and very forgiving on small, complicated roofs, the kind with six vents, two skylights and a chimney in 400 square feet. It is also the system where installer skill matters most and shortcuts burn people, sometimes literally. I’ve torched for decades, in Europe and here. Most of that work with Soprema SBS membranes, Mammouth included. Fire watch and proper detail work are not optional extras; they are the job.

Choosing a flat roof system

Most flat-roof pages on the internet are written by a company that sells one system. I install TPO, PVC and torch-on, and I’m not tied to any of them, so the advice on the torch-on vs TPO vs EPDM comparison page is the same advice I give on a roof: what suits your building, your slope, your budget and this coast’s weather. Residential flat roofs over houses, garages, carports and additions are the same conversation at a smaller scale.

And when a flat roof fails in a storm (a split seam, ponding water coming through the ceiling) that is emergency flat roof repair: tarping and temporary waterproofing to stop the water first, and the permanent fix once it is safe to work.

TPO installation in progress at Gordon Head, Victoria — a roofer kneeling on the grey membrane laying a strip along the seam
TPO installation in progress at Gordon Head: membrane going down, seams and details first. A Golden Rule Roofing job.
Finished white TPO flat roof in Saanich with sealed vent flashings and a skylight, the lake and the Olympic Mountains behind
Finished TPO in Saanich, 2016 — a clean white membrane, sealed vents and a skylight, over the lake toward the Olympic Mountains.

Flat roof projects on Vancouver Island

  • Slegg Lumber warehouse, Langford: 25,000 sq ft (2014)
  • Travelodge, Duncan: 12,000 sq ft TPO (2015)
  • The Root Cellar, Victoria: 5,000 sq ft (2015)
  • Residential flat roofs: Salt Spring Island (2015), Mill Bay, Victoria and area

Installation videos

My TPO installation series on YouTube has been watched about 165,000 times. This is the work, filmed on real Victoria roofs, seams, details and all.

CWS - TPO roofing installation Victoria, BC Part 1, 71,950 views. The full installation, start to finish.

CWS - TPO roofing installation Victoria, BC Part 3, about 70,000 views. Seam probing, patches and detail work.

CWS - TPO roofing installation Victoria, BC Part 2, about 23,000 views. Installation details and the welding robot.

The repair video, how I find and fix leaks on a TPO roof, is on the roof repair page. All of the videos, including a TPO installation on Salt Spring Island, are on the CWS YouTube channel.

Frequently asked questions

TPO or torch-on — which is better for a flat roof on Vancouver Island?

Both are good systems when installed properly. TPO is a single-ply membrane with heat-welded seams, clean, light-coloured, energy-reflective, and proven on big commercial roofs. Torch-on (SBS modified bitumen) is a two-ply system melted down with a torch; it is tough and forgiving on smaller, cut-up roofs with lots of details. Denis installs both and will tell you honestly which suits your roof. He is not tied to one manufacturer. The comparison page on this site lays out TPO, torch-on and EPDM side by side.

How long does a TPO flat roof last?

A properly installed TPO roof typically lasts 20–25 years on the BC coast. Manufacturer system warranties of 10, 15 or 20 years are available when the roof is installed to spec. The seams are the whole game: heat-welded seams are stronger than the membrane itself, while a badly welded seam is where TPO roofs fail.

How much does it cost to replace a flat roof in Victoria?

As 2026 general guidance, flat roof replacement in the Victoria area runs about $7–$15 per square foot installed (TPO typically $7–$12, torch-on $8–$15). Tear-off, insulation, slope correction and the number of details (vents, drains, skylights) move the real number. See the roof cost page for a breakdown, or ask Denis for a written estimate.

Can a flat roof be repaired instead of replaced?

Often, yes. If the membrane is sound and the insulation underneath is dry, a proper repair — new welded patches, re-done seams and flashing, can add years. If the insulation is soaked, repairs are money thrown away. Denis checks what is under the membrane before recommending anything.

How much slope does a flat roof need?

A flat roof is never truly flat. It needs positive slope to the drains, about 2% (a quarter inch per foot) in the field of the roof, built with tapered insulation on most re-roofs. Water that still sits 48 to 72 hours after rain is ponding, and ponding shortens a roof’s life. If your roof holds puddles for days, that is a drainage problem to fix, not a fact of life.

Request a flat roof quote

Big commercial roof, strata, or a flat roof over your garage. Describe it and I’ll tell you straight which system fits and what it should cost.

Roof type
How many stories?
Existing roof layers
Is the roof sheeted?
Roof pitch
Known leaks or damage?
Roof age
Is this an emergency?
When do you want the work done?
Garage attached to the house?

Prefer to talk? Call Denis or email info@waterproofingsystems.ca.

☎ Call Denis